Effects of Rogue Waves On Ships
To understand the effects of rogue or freak waves on ships at sea, it is vital to first develop an understanding of rogue waves in itself, the occurrence of such a phenomenon and the reason behind such an occurrence.
The occurrence of sea waves is an uncertain phenomenon. That is, if you consider a certain area of the sea surface, the waves passing through that area would definitely be periodic in nature, but the parameter of each wave (amplitude, time period, frequency, wave height and wavelength) will vary at a rate that cannot be determined to an exact measure.
To understand that with an example, let us suppose that a wave of height 10 meters passes through a given area on the sea surface at this instance.
Then one cannot be sure if the next wave passing through the same area on the sea surface will have the same height.
This natural uncertainty in the nature of sea surface waves makes it important for us to study sea waves in a probabilistic and statistical approach, rather than a deterministic approach.
So, we plot the probability of the occurrence of a particular wave height on what is called a histogram. The horizontal axis representing the increasing height of the wave and the vertical axis representing the probability of occurrence of a wave of the corresponding height.
In the above histogram, note the following things:
- The probability of a zero wave height is zero (which is evident, since there is no sea without a wave)
- The probability of occurrence of extremely high waves is also tending to zero
- The wave height corresponding to the maximum probability is somewhere higher than zero, in the moderate height region. These are the wave heights we see daily in a normal sea. The height corresponding to the maximum probability is the maximum probable height
- The average of the highest one-third of waves is the significant wave height (Hs). This is very important, as in, it is considered the reference point of designating a wave as a freak wave
- Any wave that has a height more than that of significant height is called a rogue wave. So, as clearly evident, the probability of occurrence of a freak wave is lower, but due to its height, the energy stored in one freak wave can be high enough to cause damage to ships
To know what effects rogue waves have on ships, we need to know the motion of a ship in a wave. When a ship operates in head seas, it experiences pitching coupled with heaving motions.
The more the amplitude of the encountering wave, higher is the pitching and heaving amplitude.
Extreme combined motions of pitching and heaving in ships result in the forward part of the ship plunging into the sea surface after it encounters a wave.
So, in some cases, when the sea state is high, there is a probability of increased height of waves that a ship may encounter.
Sometimes, these waves may be higher than that corresponding to significant wave height, which is called freak waves or rogue waves.
The problem with such waves, is that they cannot be predicted, owing to the natural uncertainty of sea waves.
Effects on a ship because of rogue waves
Bow Slamming
When a ship encounters high waves (especially in head seas), high amplitude pitching and heaving combined produces an effect that sends the bow out of the water. As the wave passes aftward, the bow falls onto the surface (or slams the surface), with high acceleration, resulting in tremendous slamming forces in the forward structure of the ship.
Formation and Propagation of Cracks
Due to high slamming and pounding forces in the forward structure, the hull at the bow section is often prone to cracks that can propagate over the entire depth of the bow section.
Buckling of plates
The shell plates at the bow and the bottom plating up to 25 per cent of the ship’s length aft of the forward perpendicular are subject to effects of slamming which result in buckling of these plates.
Especially the bottom plating in the forward region, because in most lading cases, the ship is in hogging condition, which maintains the bottom shell in a state of compression.
Major augment of stresses in the bottom plating, therefore, result in exceeding the buckling stress of the material, which may be much lower than the ultimate tensile stress.
Ultimate Failure
When forward structures have been subjected to a large number of cycles of freak waves or slamming forces over a longer period of time, the structure undergoes fatigue.
If scantling and structural surveys are not carried out regularly, then ultimate failure, leading to complete rupture of bow sections is not an impossibility when encountered with freak waves.
So designers have over the years, developed methods to combat freak waves by incorporating various factors of safety in structural design. Broadly, we will discuss them under the following distinctions:
Inclusion In Structural Formulae
When the scantlings of a ship are calculated in the preliminary design phase, designers use empirical formulae suggested and tested by classification societies.
These formulae have been developed over extensive observation and analyses of statistical data of stressed that ships are subjected to at sea, and accordingly, a factor of safety is considered in determining the scantlings, so as to prevent failure due to waves that are above the significant height.
Additional Strengthening Against Slamming
The hull girder is additionally strengthened at the bow. Some of the additional structures that are included are discussed below:
- Panting stringers that run longitudinally, are welded to the side shell forward of the collision bulkhead. The height between subsequent stringer is usually 2 to 2.5 meters
- Panting Beams run transversely inside the deck shell, joining the panting stringer to the centreline wash bulkhead
- Angled pillars are used to support the panting beams at the centreline
- Panting web sections or perforated flats are used after between every one or two panting stringers. The side frames are end connected to these and the panting stringers via tripping brackets to ensure smooth stress flow
- Plate floors are used at every frame space ahead of the collision bulkhead
Navigational Measures Taken On-Board
Navigational measures are also taken on board a ship, to combat rogue waves, especially in high sea states. Remember the initial paragraphs of this article where we discussed pitching and heaving motions induced onto a ship? The idea of navigational measures is just to reduce the pitching amplitudes.
The pitching amplitudes depend on the encountering angle and the encounter frequency. The encounter frequency is changed by changing the speed of the ship, and the encounter angle is altered by changing the heading of the ship.
Though the latter may not always be feasible on fixed routes, the former is mostly used to reduce unwanted motions on the higher side.
Over to you..
Are you aware of any other effects of rogue waves on ships?
Let’s know in the comments below.
You might also like to read:
- Different Types of Sea Waves – A Comprehensive List
- What are Rogue Waves?
- What Actions Ship Must Take For Tropical Revolving Storm (TRS)?
- Top 10 Amazing Ocean Mysteries and Phenomena
- 10 Deepest Parts of the Ocean
Do you have info to share with us ? Suggest a correction
Latest Marine Navigation Articles You Would Like:
Subscribe To Our Newsletters
By subscribing, you agree to our Privacy Policy and may receive occasional deal communications; you can unsubscribe anytime.
Web Stories
thanks for this article.
rogue waves have many and complexe effects on ship sailing in worse sea condition. one of them is the loading of water on deck; and can make the ship in an new load condition to affect dynamic stability
University lecturer at marine engineering department- Algeria
Thank you for your valuable input @Abdeljalil
This has resulted in sinkings. Pitchpole or rollover or submarine like edmund fitzgerald