Types of Vibrations On Ships – Machinery Vibrations
One of the most common and dreaded problems onboard ships is high levels of vibration. The two most noticeable effects this vibration has on the ship is structural fatigue and discomfort of crew/passengers.
In the past, there have been ships that have been discarded for years due to an unacceptable level of vibrations, rendering them unsafe for operation.
So, over the years, with research by classification societies, a lot of improvement has been achieved in terms of marine vibrations.
Design techniques have undergone changes to incorporate factors related to the reduction of vibration levels during the entire lifespan of a ship.
This article is not about the basics of vibration mechanics. It is about the categories of vibration onboard ships, the basis of their categorisation, insight on the origin of each type of vibration, and design techniques adopted to prevent them.
So it is assumed henceforth, that the very basic fundamentals of vibration are well known to the reader.
To begin with, vibration ships are majorly categorised into two types, depending on the components of the ship the vibration is primarily related with. They are:
- Type One- Machinery Vibration
- Type Two- Hull Vibration
In this article, we will only on ‘Type One – Machinery Vibration’, and in the next, ‘Type Two – Hull Vibration’.
Machinery Vibration
The vibrations that originate due to the operation of machinery can be listed under Machinery Vibrations. Any machinery that has parts moving at a certain frequency induce vibrations.
So, main engines, propulsion shafts, gearboxes, propellers, pumps, diesel generators- all machinery transmit vibrations.
The role of a ship designer is to first understand how each of these machinery causes vibrations and then device methods to keep them within safe levels. Machinery Vibrations can again be categorised into three types, depending on the nature of the vibrations:
- Torsional Vibration.
- Axial or Longitudinal Vibration.
- Lateral Vibration.
Torsional Vibration
The main propulsion system of a ship consists of the main engine, which is connected to a propeller by a shaft. The shaft is again, not a single component.
Usually, a marine shaft consists of an intermediate shaft and a propeller shaft, which are connected by means of coupling flanges.
The presence of connections, like coupling flanges, thrust block, engine connection flange, and the cylinder-piston system in the main diesel engine creates torsion in the rotating shaft system.
In other words, the rotatory motion of the diesel engine creates an ‘excitation’. So, the entire propulsion system can be simplified, for vibrational analysis into a series combination of shafts and discs, as shown in the figure below:
The above system of shafts and discs deduced from the proposed propulsion system of a ship to be designed, is used to calculate the natural torsional frequency of the propulsion system.
The task of a designer is to choose the main engine such that the natural frequency of the main engine at its MCR is not within 5% of the natural torsional frequency of the entire propulsion system. Or in other words, the approach can be reasonably generalised stating that, the excitations should be minimised so as to prevent resonance.
According to the speed range at which torsional resonance occurs, the barred speed range is set, so that this speed range is avoided during the voyage. If that is not taken care of, it would result in a torsional failure of the shaft.
Axial or Longitudinal Vibration
One of the most interesting cases of machinery vibration, and perhaps the one most likely to cause forced vibrations, is axial vibration of the propulsion system.
As we saw earlier, to analyse a case of vibration, it is important to identify the excitation of a particular type of vibration.
Axial mode of vibration makes the propulsion system behave like a horizontal multiple degrees of freedom spring-mass system. So, the propulsion system in figure one can be reduced to a system as shown below in Figure 2.
Now, for a while, let us shift attention from this system and focus on the operation of the propeller. The thrust generated by the propeller depends on the velocity of water incident onto the propeller blades (called wake).
Now, due to the curvature of the hull at the aft, the wake on the propeller is not uniform in nature. That is, the wake at the top of the propeller disc is different from the wake at the bottom of the disc. To obtain a better idea about the variation of a wake, follow Figure 3.
It shows the variation of wake at different angles around the propeller disc. This diagram is only for a particular distance from the centre of the propeller disc (shown in blue).
So it should be well understood, that the wakes for each distance from the centre of the propeller centre will have different graphs.
What we, therefore, imply from the above diagram is, when a particular blade of the propeller is at the 0-degree position, the velocity of water onto it is different from the velocity of water onto the same blade when it has rotated to 90-degree position.
And this variation is continuous across one half of the propeller rotation. As a result of this, the thrust generated by that blade at zero degree position will be different from the thrust generated by the same blade at 90 degrees and 180 degrees.
And this is repeated with each revolution, which means that the thrust generated by the propeller is periodic in nature, which we often call as alternating thrust. And a periodic thrust becomes the exciting force for the axial vibration of the propulsion system.
The frequency of the propeller excitation is (Propeller RPM x Number of blades). In order to avoid resonance, the designer must ensure that the first few natural frequencies of axial vibration of the main propulsion system (shown in figure 2) are at least 5% away from that of the propeller excitation frequency.
A Quick Question: What steps must a designer take if the propeller excitation frequency lies within the first few natural frequencies of longitudinal vibration of main propulsion system?
In such a case, there are two major options. One, either the propeller excitation frequency needs to be changed, or the natural frequencies of the main propulsion system have to be altered. Before going into the procedure of doing that, let’s first look into the feasibility of each option.
Option One- Changing the propeller excitation frequency
In order to change the propeller excitation frequency, either the number of propeller blades has to be changed, or the rated RPM of the propeller has to be altered.
Changing the number of propeller blades is not a feasible option because the number of blades has a high influence on the efficiency of the propeller.
At this stage of the design, the rated RPM of the propeller has already been decided upon on the basis of required torque and thrust to provide the effective power required by the ship. So, altering the rated RPM is not a viable option either. It is clear, Option One cannot be implemented.
Option Two: Changing the natural frequency of Main Propulsion System
This option is feasible because taking this step wouldn’t affect other factors of the ship. But how does one go about this process?
The natural frequency of any system depends on the stiffness and the mass of the system. Changing the mass of the propulsion system is not an intelligent approach. Instead, ship designers focus on playing with the stiffness of the system.
How? Well, the primary focus is on the thrust bearing and its foundation. The foundation of the thrust bearing is the component that deflects in response to the thrust that is transmitted by the thrust bearing.
In other words, it behaves as a spring. So the structural foundation of the thrust bearing must be redesigned to obtain a stiffness that would change the natural frequency of the propulsion system to the desired value.
Lateral or Transverse Vibration
This mode of vibration occurs in the direction perpendicular to the axis of rotation of the shaft. The intermediate and tail shafts can be considered as beams, with the shaft bearings as support points.
Due to the bending of the shafts, the centre of gravity of the shaft does not coincide with the ideal centreline of the shaft, therefore when the shaft rotates, the centrifugal force on the centre of gravity would cause it to shift further away from the ideal centreline, resulting in a vibratory motion called whirling of shafts.
The number of shaft bearings and the distance between them is the deciding factor in the occurrence of this mode of vibration, during the design phase.
Care is to be taken by the designer that the natural frequency of lateral mode of vibration of the shaft does not coincide with the natural frequency of the engine.
In such a case, resonance would result in the extreme case of whirling, which would lead the shaft to snap and cause damage or accidents.
Also, when the engine of a ship is started, and its speed gradually increased, there comes a point when one would feel maximum vibrations on the ship for a few moments.
That is because, there during the speeding up, there arrives a point at which the RPM of the engine coincides with the natural whirling frequency of the shaft.
Such speed / RPM is to be carefully avoided. This speed is called Critical Speed, or Barred Speed Range.
A ship is never to be operated at this speed range, and during speeding up, this speed range should be passed as quickly as possible so as to prevent prolonged shaft vibrations.
Now, to visualize the source of whirling with added clarity, let us relate to Figure 4 and 5. Figure 5 shows the cross-section of the shaft at mid-length after bending has occurred.
Now, when the shaft rotates, the centre of gravity will not coincide with the centreline of the shaft, resulting in different trajectories of the centre of gravity of the shaft as shown in Figure 6.
Sources of Whirling Vibration
A ship designer must very well know the sources of whirling vibration so as to take proactive measures. We will discuss them in brief below:
Propeller Fluctuating Loads
As we have seen earlier, the varying wake onto the propeller, the effective thrust provided by the propeller is not always along the shaft centreline, but at some angle to the centreline of the shaft.
This exerts bending stress onto the shaft, resulting in whirling. Also, as the angle between thrust and shaft centreline changes periodically, various modes of whirling are observed.
To counter this issue, the shaft is pre-aligned such that in operating conditions, this effect is minimised.
Diesel Engine Excitation
The moving parts of the diesel engine act as a primary source of excitation for whirling. The grass pressures in the engine act as exciting forces.
The radial components of the gas pressure are responsible for the whirling vibrations, whereas, the tangential components are responsible for torsional vibration.
The data of gas pressure in engines are provided by engine manufacturers, and the shafting system is designed with the data into consideration.
Shaft Alignment Errors
If the centrelines of the shaft coupling flanges are not carefully coincided during shaft alignment at the shipyard, it results in loss of the continuity of the rotation axis of the shaft.
Another coupling defect that can lead to whirling is when all the coupling bolts through the coupling flanges are not equally tightened to the same extent, causing an angular misalignment between the coupling flanges.
Such kind of errors will excite the first mode of whirling excitation and must be avoided with proper shipbuilding practices.
Manufacturing Defects in Gearing System
Whenever gearing equipment is being installed, proper mounting and pairing are necessary to avoid whirling induced from improper gearing. Such defects often give rise to high frequency whirling modes.
But this is something that needs to be taken care of in the construction phase, and cannot be taken into consideration in vibration analysis during the design phase.
So, in this article, we have looked at machinery vibrations and discussed how each type of vibration is excited and can be prevented.
What, however, we have not looked into, is that there are among these, some excitations, which not only cause vibration in the propulsion system, but also caused forced vibrations in the hull girder, which is even more dangerous, and will be discussed in detail in the next article.
You might also like to read:
- Different Ways To Reduce Ship Propeller Vibrations And Increase Its Efficiency
- Types of Vibrations On Ships – Hull Girder Vibration
- Understanding Design Of Ship Propeller
- Understanding Vibrations in Marine Engines
- Dampers & De-tuners: Reducing Vibration of Marine Engines
Disclaimer: The authors’ views expressed in this article do not necessarily reflect the views of Marine Insight. Data and charts, if used, in the article have been sourced from available information and have not been authenticated by any statutory authority. The author and Marine Insight do not claim it to be accurate nor accept any responsibility for the same. The views constitute only the opinions and do not constitute any guidelines or recommendation on any course of action to be followed by the reader.
The article or images cannot be reproduced, copied, shared or used in any form without the permission of the author and Marine Insight.Â
Do you have info to share with us ? Suggest a correction
Latest Naval Arch Articles You Would Like:
Subscribe To Our Newsletters
By subscribing, you agree to our Privacy Policy and may receive occasional deal communications; you can unsubscribe anytime.
Web Stories
Excellent
where can i find the the second part of this article – Hull Vibration
Hey great read I must say And I must appreciate you for your knowledge behind this. Thanks for such a useful information.
@Raj: Glad the content is useful for fellow seafarers.
It lacks the actual dynamics of forces which result in vibrations.There is no information about the dead weight of engine components,centrifugal forces at crank,peak pressureswhich are affecting the vibration.There is no information about dynamic and static loading of forces and its effectwhich marine engineers are more concerned about